SAFETY DATA SHEET (SDS)
Epoxy Resin (Component A)
According to GHS Revision 7
Revision Date: 11 July 2025
SECTION 1: IDENTIFICATION
1.1 Product Identifier:
Product Name: Epoxy Resin (Component A)
Product Code: [CK-ART1001]
1.2 Recommended Use: Thermosetting polymer for coatings, adhesives, composites, electronic encapsulation,
industrial flooring, etc.
1.3 Supplier:
Guangdong Crekoat New Materials Co., Ltd.
NZ Division Address: 410 Linwood Avenue, Bromley, Christchurch 8062, New Zealand
Tel: +6421966387
Email: resinwoodtablesnz@gmail.com
1.4 New Zealand Official Distributor:
RESINZWOOD LIMITED
24-Hour Emergency Tel: +6421966387
SECTION 2: HAZARD IDENTIFICATION
2.1 Classification: Not classified as hazardous under GHS Rev. 7.
2.2 Label Elements:
Symbols:
Signal Word: Warning
Hazard Statements: None
Precautionary Statements: P501 (Dispose of contents/container per local regulations).
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1 Mixture:
Epoxy oligomer (e.g., Bisphenol A diglycidyl ether): 95–100%
Non-hazardous additives (e.g., viscosity modifiers): 0–5%
CAS No.: 24969-06-0
No hazardous ingredients above GHS thresholds.
SECTION 4: FIRST AID MEASURES
4.1 General:
Skin Contact: Wash with soap and water.
Eye Contact: Rinse the eye with water for 15 minutes. Seek medical advice if irritation persists.
Ingestion: Rinse mouth. Do NOT induce vomiting.
Inhalation: Unlikely; move to fresh air if discomfort occurs.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1 Containment: Absorb with inert material (sand, vermiculite).
6.2 Cleanup: Collect in sealed containers. Avoid dust formation.
SECTION 7: HANDLING AND STORAGE
7.1 Handling: Use in well-ventilated areas. Avoid skin/eye contact.
7.2 Storage: Keep in tightly sealed containers at 10–30°C. Away from oxidisers.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 Engineering Controls: General ventilation is sufficient.
8.2 PPE:
Gloves (nitrile)
Safety goggles
Lab coat
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Property Value
Appearance: Clear, viscous liquid
Odour Mild, characteristic
Boiling Point >200°C (decomposes)
Flash Point >150°C (non-flammable)
Density 1.1–1.2 g/cm³ (20°C)
Solubility in Water Insoluble
SECTION 10: STABILITY AND REACTIVITY
10.1 Stability: Stable under recommended conditions.
10.2 Hazardous Reactions: Reacts exothermically with amines/acids (Component B).
10.3 Incompatible Materials: Strong oxidisers, acids, bases.
SECTION 11: TOXICOLOGICAL INFORMATION
11.1 Acute Effects:
Low oral/dermal toxicity (LD50 > 2,000 mg/kg).
May cause mild skin/eye irritation.
11.2 Sensitisation: Not classified as a skin sensitiser.
SECTION 12: ECOLOGICAL INFORMATION
12.1 Aquatic Toxicity: Low toxicity (LC50 > 100 mg/L for fish).
12.2 Persistence: Not readily biodegradable.
SECTION 13: DISPOSAL CONSIDERATIONS
13.1 Waste Disposal: Dispose of as non-hazardous industrial waste per local regulations.
SECTION 14: TRANSPORT INFORMATION
14.1 DOT/IMO/IATA: Not regulated for transport.
SECTION 15: REGULATORY INFORMATION
15.1 GHS Compliance: Fully compliant with Rev. 7.
15.2 NZ Regulations: HSNO Notified (Non-hazardous).
SECTION 16: OTHER INFORMATION
16.1 SDS Preparation: Prepared by Guangdong Crekoat New Materials Co., Ltd.
16.2 Disclaimer: Use only with Component B per technical guidelines.
16.3 Revision Date: 11 July 2025
New Zealand Emergency Contact:
RESINZWOOD LIMITED | 24hr Tel: +64 21966387
Disclaimer:
The information provided in this Safety Data Sheet (SDS) is based on Resinzwood's current level of knowledge and is intended to describe the safety characteristics of this product. It does not constitute a guarantee of the specific properties of the product, nor is it considered a commitment to liability for infringement of any patent rights. Users should evaluate the safety and suitability of this product based on their specific operating conditions, purpose requirements and compliance with applicable liability laws and regulations. The recommendations in this SDS are only for this product itself and do not include the risks that may exist when it is mixed with other substances or in specific processes. The recipient is responsible for ensuring that its employees, customers and downstream users obtain and understand the information in this SDS and take appropriate safety precautions.
